4.1.5. Removal and installation of a forward suspension bracket

Removal
Install the car on the elevator or a viewing ditch and slow down it the parking brake, take off a wheel cap, weaken bolts of fastening of a forward wheel and turn off a nut of fastening of a nave. Having lifted a forward part of the car, remove a forward wheel.

Fig. 4.3. Vypressovka of a finger of the spherical hinge of steering draft from the rotary lever of a rack of a suspension bracket: 1 – rotary lever; 2 – spherical hinge of draft; 3 – stripper And. 47035

Stripper And. To 47035 vypressuyta a finger of the spherical hinge of steering draft from the rotary lever of a rack of a suspension bracket (fig. 4.3). Disconnect a rack 24 (see fig. 4.1) the stabilizer of cross stability from the lever 22 suspension brackets and an arm of the 30th extension from a body. Disconnect the spherical hinge of the lever of a suspension bracket from a rotary fist.

       NOTE
At an otvertyvaniye of bolts of fastening of the spherical hinge to a rotary fist use only a face key not to damage a protective cover of the hinge.

Disconnect the lever 22 suspension brackets from an arm of the 28th body and remove the lever assembled with an extension 29 and an arm 30.
Turn off bolts of fastening of a guide of blocks to a rotary fist 13, assembled with blocks suspend a support on a technological hook to a body so that the hose was not loaded.
Taking aside and turning a rack 9, by means of adaptation 67.7823.9544 to a vypressuyta from a nave of a wheel shlitsevy a shaft of the 18th hinge of equal angular speeds.
From a compartment of the engine take off a protective cap of 41 support, turn off nuts of fastening of a telescopic rack to a mudguard of a body and remove a rack of a forward suspension bracket assembled with a rotary fist and a nave of a wheel.
Carrying out the specified operations, remove other rack of a forward suspension bracket. Then remove from a bar of the 25th rack 24, turn off nuts of fastening of the stabilizer of cross resistance to a body and carefully bring a stabilizer bar out of a reception pipe of the muffler.
Installation
You carry out installation of knots and details of a suspension bracket to the sequences, the return to removal taking into account the following:
– forward nuts of extensions, nuts of bolts of fastening of levers of a suspension bracket to arms of a body, a nut of fastening of racks of the stabilizer to cross levers of a suspension bracket and nut of fastening of a bar of the stabilizer to a body previously tighten before the choice of gaps in joints;
– all nuts, the fixing rubber-metal hinges, rubber plugs and pillows, finally tighten the moments specified in the appendix 1 at static load of 3136 N (320 kgfs) (four persons) and 392 N (40 kg of freight in a luggage carrier);

Fig. 4.1. Forward suspension bracket assembled: 1 – top support of a telescopic rack; 2 – top basic cup; 3 – the compression course buffer with the protection cover; 4 – compression buffer support; 5 – suspension bracket spring; 6 – lower basic cup of a spring; 7 – spherical hinge of steering draft; 8 – rotary fist; 9 – telescopic rack; 10 – eccentric washer; 11 – adjusting bolt; 12 – rack arm; 13 – rotary fist; 14 – protection cover of a forward brake; 15 – disk of the brake mechanism; 16 – lock ring; 17 – wheel nave nut; 18 – shlitsevy wheel drive hinge case shaft; 19 – the directing pin; 20 – wheel bearing; 21 – spherical hinge; 22 – suspension bracket lever; 23 – adjusting washers; 24 – stabilizer rack; 25 – stabilizer bar; 26 – stabilizer bar pillow; 27 – arm of fastening of a bar of the stabilizer; 28 – a body arm for fastening of the lever of a suspension bracket; 29 – suspension bracket lever extension; 30 – arm of fastening of an extension; 31 – protective cover of a spherical finger; 32 – bearing of a spherical finger; 33 – spherical finger; 34 – case of a spherical finger; 35 – suspension bracket rack rod; 36 – external case of the top support; 37 – internal case of the top support; 38 – bearing of the top support; 39 – rubber element of the top support; 40 – limiter of the course of the top support; 41 – protective cap of the top support; In — a zone for control of the hinge of a suspension bracket

– at installation of an arm 30 (see fig. 4.1) fastenings of an extension to a body you watch to damaging a carving in welded plugs of a body;
– at installation of the stabilizer of cross stability do not allow the longitudinal shift of pillows on a bar as they have to hold strictly certain position (see subsection. "Dismantling and assembly of knots of a suspension bracket").